Your RBW 15,000 pound hitch should fit in the Reese rails unless they are installed improperly. When the hitch was installed on the F-550 it may have been tightened down with the gooseneck adapter installed and the rails are just out of position for your fifth-wheel hitch. If the hitch you have is not fitting by a small amount I would try to loosen the mounting bolts on the rails and then install the fifth-wheel hitch. After you have the hitch installed you can then re-tighten the mounting... view full answer...
On the back of your factory 7-Way trailer connector on your 1997 Ford F-150 the wiring harness should plug into the back of it meaning it can be removed. If that is indeed the case with yours then you can install 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End Item # HM40975 in its place. I have linked a video that shows installation for you.
I do not anticipate a problem because all of the replacement 7-Ways listed for your truck install in the same way. view full answer...
It sounds like you have done a good job in choosing the correct items for installing a brake controller on your 1998 Ford F-150 XLT with factory tow package. Everything you have chosen is the correct part for your application.
The Tekonsha P3 Brake Controller # 90195 and the Ford Adapter # 3035-P is a good choice for your vehicle. The P3 brake controller is a proportional brake controller which means it will only activate when you apply the brakes on the tow vehicle. It has a motion sensing... view full answer...
The The Original Custom Towing Mirror Slide-On Mirrors, # CTM2300 or a confirmed fit for OEM mirrors such as the one in attached image. If your specific vehicle has mirror that match shape in image this will fit. Please see the attached video these mirrors on same generation F-150. view full answer...
Tonneau covers and ladder racks can be compatible with each other when they do not use the same mounting points on the truck bed rails. Both tonneau covers and ladder racks can mount either inside the bed rails or on top of them.
As an example, the TracRac SR sliding ladder racks like # TH43002XT-501 mount on top of the bed rails so they will work with tonneau covers like Tonno Pro soft roll-up cover # TPLR-3080 which installs inside the bed rails.
Please feel free to email me back with... view full answer...
I'm not quite sure what you mean but I'm assuming since you were looking at a tailgate assist that that's what you're looking for. If that's the case then the DeeZee Tailgate Assist Custom Tailgate-Lowering System # DZ43203 would be a confirmed fit as long as your 1998 Ford F-150 isn't a stepside or flareside model. view full answer...
We have a couple Westin bumpers that fit your 1998 Ford F-150 but part # 31016 fits certain model years of the Dodge Dakota and not your truck.
Instead we have part # 31002 which is chrome plated bumper that will fit your F-150 but we don't currently have a black powder coat bumper that does. view full answer...
If your 1997 Ford F-150 came with a factory 7-Way or 4-Way then you can use the brake controller wiring adapter # 3035-P for Tekonsha brake controllers, or # HM47715 for a Hopkins brake controller. I have included a link to the installation details for the Hopkins and Tekonsha harnesses for you to view. view full answer...
For your 1999 Ford F-150 the Curt front hitch part # 31038 has been confirmed as a fit and would work well. The fit info we have for this hitch is that it is for trucks with front tow hooks like yours so it will fit. view full answer...
The good news is that programmers are made for specific models and specific years and I do have a couple tuners that will fit your 1999 Ford F-150 5.4L XLT and will work with your cold air intake. The Superchips Dashpaq Performance Tuner - 2.4" Color Screen - Gas - Ford # SU1060, has a 2.4 inch color screen and will help you show gains in both horsepower and torque.
The other tuner is the Edge Gas Evolution CS2 Performance Tuner, # EP85350. This is very similar to the Supechip Dashpq.... view full answer...
The aftermarket performance tuners/monitors that we offer for your 1999 Ford F-150 XLT with 5.4L V8 engine are shown on the linked page. The Edge Evolution Programmer # EP15051 fits only later model years, 2004 through 2008.
The Superchips Dashpaq Performance Tuner - 2.4" Color Screen - Gas - Ford # SU1060. which can use used along with the custom dash mounting pod # EP18550. This tuner can deliver power gains in both horsepower and torque. It can be stacked with a cold air intake provided... view full answer...
Thanks for your recent brake controller and wiring adapter purchase!
Yes, the Tekonsha Primus IQ brake controller # TK90160 should work with the Curt adapter 4 pole to 7 pole and 4 pole # C57674 with the integrated test lights. In the past, there were some situations where the test lights illuminated with the small signal that the brake controller sends to detect a trailer. Our representative at Cequent Performance hasn't had any customer issues regarding the Primus IQ with test lights.
I... view full answer...
Thanks for the photo and based on that we do have a replacement that will work for you although you are going to need to know what your gray water pipe and black water pipe connections are - either spigot or hub - which I'll explain but you are going to need to remove your valve to find this out.
Basically, hubs on the valves slide OVER your RV's water lines while the spigots on the valves slide INTO the water lines. When you take off your current valve, pay attention to if it slides into... view full answer...
I spoke with my contact at Curt and he told me you can install the Curt Front Mount Hitch, # 31049, on your 1998 Ford F-150 2WD as long as the frame of your truck matches the width of the bolt holes on the hitch. The frame width should be the same between the 2WD and 4WD models, but I would recommend measuring just to verify. The bolt holes that mount to the underside of the frame rail measure 31-7/8 in. from center to center. If your frame rails approximately 31-7/8 in. apart on center,... view full answer...
Yes, your 15K Reese 30038 5th wheel hitch is compatible with the Reese Universal Base Rails and Installation Kit # RP30035 which is also a fit for your 1999 Ford F-150/F-250 Light Duty that you input for your vehicle info.
If you don't already have a 7-Way in the bed of your pickup then I also recommend installing the Curt # C56070 to make connecting your trailer wiring much easier. view full answer...
The correct replacement for the Westin E-Series Round Nerf Bars that fit a 1997 Ford F-150 will depend on what cab size you have on your truck.
- Regular Cab: Replacement Installation Hardware Kit for Westin E-Series Round Nerf Bars # 23-110PK
This kit fits the Westin E-Series Round Nerf Bars # 23-1100 (Chrome) and # 23-1105 (Black)
- SuperCab: Replacement Mounting Hardware Kit for Westin E-Series Round Nerf Bars # 23-111PK
This kit fits the Westin E-Series Round Nerf Bars # 23-1110... view full answer...
The Camper Hold Downs, part # HSSF, may work on your 1998 Ford F-150. The hold downs do not fit in the stake pockets but wrap around the bed rails and are mounted inside the bed. There is no weight capacity rating on the hold downs and they will work for any camper size that is properly sized for your vehicle.
I added a picture of this product loosely installed on a truck bed to show you how it fits.
The Camper Tie Down Hardware Package, item # TDHP is recommended for use with these camper... view full answer...
The Hopkins Universal Mounting Bracket # HM48625 will allow you to mount the Hopkins Endurance Quick-Install 7-Way Trailer Connector # HM47210.
Be sure to use Dielectric Grease # 11755 on the connector to prevent shorts in the connectors. view full answer...
My first suggestion would be to contact your Jayco in order to determine if they recommend using a hitch on the rear of your 2005 Jayco JayFeather M-19H. You will want to provide them with your VIN for the most accurate information. If they ok the use of a hitch, ask them for the recommended weight capacity. This will be the maximum amount of weight that can be safely hauled on the back of the trailer.
A couple measurements will need to be taken in order to see if the Adjustable Width... view full answer...
The 1998 was available with at least three different types of mirrors, to match the existing mirror with an available slip-on mirror, take a look at the photo we edited for you.
Part # 11953is sold individually, and will fit either the driver or passenger side.
Part # 11601 fits the driver side, and # 11602 fits the passenger.
Part # 11701 fits the driver side, and # 11702 fits the passenger. view full answer...
Go To Results